Kenmore 110.47511701 washer quits mid cycle randomly


Kenmore 110.47511701 washer quits mid cycle randomly

Author
Message
jengel
View Quick Profile

Forum Member
Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)

Group: Awaiting Activation
Last Active: 9 Months Ago
Posts: 4, Visits: 31
Came with the house, just want it to limp along for a few more months if possible.

Symptoms:   Randomly it will rinse, but not spin all of the water of the clothes, it just shuts off.   Or it'll run for 5 minutes and just decide to shut off.     No rhyme or reason we can figure out.

sometimes we'll put it on Rinse and spin, it will shut off randomly too.   We've gone a few weeks with zero issues, but after the last power outage (this may be the key) it's gotten WAY worse.

This morning, put a load in, pushed start, the door locked and it just sat there looking at me, almost mockingly.   Then it shut off.   Door still locked.  Turn it off, turn it back on, push start again, here a click, then it did it again.   I was about to open the kick panel to pull the manual release (I think they all have that) and I decided to unplug it for 15 minutes, plugged it back in and it released when I hit the power button.

Zero error codes, but I don't know if there is a way to pull them up.

controller board?   Evil gnomes? 
Attachments
20191024_150528.jpg (77 views, 2.00 MB)
Edited
9 Months Ago by jengel
FixItUp
View Quick Profile

Supreme Being
Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)

Group: Moderators
Last Active: 4 Months Ago
Posts: 808, Visits: 6.6K
I was able to locate the tech sheet for the model number provided (please see attached). See if any codes appear after doing a diagnostics mode test and we can go from there!

Attachments
Tech Sheet.pdf (73 views, 545.00 KB)
jengel
View Quick Profile

Forum Member
Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)

Group: Awaiting Activation
Last Active: 9 Months Ago
Posts: 4, Visits: 31
F-28  Serial Connection Error
jengel
View Quick Profile

Forum Member
Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)

Group: Awaiting Activation
Last Active: 9 Months Ago
Posts: 4, Visits: 31
To add.  After it ran through the Automated test, the door will not unlock again.

F29 error added to the F28.

Main Harness issue? 
Edited
9 Months Ago by jengel
FixItUp
View Quick Profile

Supreme Being
Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)Supreme Being (73.8K reputation)

Group: Moderators
Last Active: 4 Months Ago
Posts: 808, Visits: 6.6K
Were you able to follow the procedures associated with the codes as outlined in the tech sheet?
jengel
View Quick Profile

Forum Member
Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)Forum Member (400 reputation)

Group: Awaiting Activation
Last Active: 9 Months Ago
Posts: 4, Visits: 31
FixItUp - 10/25/2019 3:57:47 PM
Were you able to follow the procedures associated with the codes as outlined in the tech sheet?

Sorry for the delay.   I was able to perform the tests last night.   Everything I checked out.  No opens, no grounds in the wires.  I went through and unplugged everything I could find and re-seated.  I also loosened all grounds and re-tightened. 

So far, everything is working.   We'll see how long this time. 
Admin
View Quick Profile

Supreme Being
Supreme Being (151K reputation)Supreme Being (151K reputation)Supreme Being (151K reputation)Supreme Being (151K reputation)Supreme Being (151K reputation)Supreme Being (151K reputation)Supreme Being (151K reputation)Supreme Being (151K reputation)Supreme Being (151K reputation)

Group: Administrators
Last Active: 5 hours ago
Posts: 2.3K, Visits: 12.9K
Great, good luck maybe it won't give you any more trouble Smile








Reading This Topic